Artikel-Nr.: A1553
- Beschreibung
Description
This is a new revolutionary product from X Power for MR03 front
suspension. It has a "3 in 1" feature which embedded "Camber
Adjustment", "Ride Height Adjustment" and "Caster Function" in one
product.
It is highly compatible to Kyosho’s products. The Camber Adjustment and
Ride Height Adjustment can be used with Kyosho’s stock and option front
suspension arms. Given Camber Function requires moving backward the
suspension arms, it is highly recommended to use together with X-Power’s
suspension arms for the best result. The use of this product will not
cause any problem for continue use of low front profile shell like HSV.
Camber Adjustment
The beauty of this product is to adjust the front wheel camber from 0
degree to 3.5 degree very easily without changing the steering knuckles.
All need to do is to loosen the screws of Camber Adjustment parts and
adjust them accordingly. 4 cubes (0, 1, 2 & 3.5 degree, refer to
Remark below) are provided to assist adjustment to ensure cambers of
right and left wheels are the same.
Suspension arms provide camber gain effect when the arms move up.
Placing washers under the steering knuckles to adjust the ride height
makes the ultimate camber different from what was indicated on the
steering knuckles. This product can help to fine tune the final camber
to the level you want.
Ride Height Adjustment
The stock set up of MR03 does not allow you to lower the ride height to
a large extent. When placing too many washers under the steering
knuckle to lower the ride height (when using new tyre), the resting
angle of suspension arms will become "v" shape which means that the
springs were pre-load too much. The front suspension will become too
hard even soft springs were used. To overcome this, the only ways are
either to use thinner tyres or cut/shorten the springs (which is highly
not recommended).
This product can adjust the suspension arms resting angle to ensure it
will stay as "—"shape even after washers were used to lower the ride
height of car.
Caster Function
By inter-changing the right and left side of Ride Height Adjustment
parts, this product is able to provide Caster function. Front caster is
not commonly used in Mini-z. The benefit of it is to provide greater
camber gain effect at low speed cornering (as the speed of the car is
not high enough to kick in the camber gain effect of suspension arms).
Also, it can strengthen the centering force of steering knuckles after
exiting the corner.
Recommended Set Up Procedure
In view this is a "3 in 1" product, below is the set up procedure for easy reference.
1. Recommend to use 0 degree knuckles to start with and then place
washers under the steering knuckles to achieve the best ride height.
2. If new tyres were used, you will notice that the resting angle of
suspension arms will become "v" shape (since too many washers were used
to lower the ride height).
3. Loosen the screws of Ride Height Adjustment parts to adjust the
resting angle of suspension arms to make it become "—" shape again.
4. Lastly, adjust the camber by using the cubes provided. You may
notice that the resting angle of suspension arms might change slightly,
repeat step 3 above for fine tuning.
5. If you would use the caster function, inter-changing the right and
left side of Ride Height Adjustment parts. Then repeat step 1 to 4 again
to achieve the best setting you want.
Note:
The cubes (0 to 3.5 degree) provided are to help adjusting camber to
ensure the ultimate camber of right and left wheels are the same. The
indicated degree thereon does not necessary imply the final camber of
the wheels as it was explained above that the camber of each wheel is
depending on the ride height of the car (as there is camber gain effect
of suspension arms).
Durchschnittliche Kundenbewertung:
Anzahl der Kundenbewertungen: 0